omdazz_WS2812b.v

@@ -2,10 +2,8 @@ module omdazz_WS2812b #(
     parameter integer WS2812_NUM   = 10 - 1,
     parameter integer WS2812_WIDTH = 24,
     parameter integer CLK_FRE      = 50_000_000
-	 //parameter [WS2812_NUM:0] LED_MASK 
 )(
     input  wire CLOCK_50,
-	 input  wire [WS2812_NUM-1:0] LED_MASK,
     output reg  WS2812
 );
 
@@ -29,10 +27,6 @@ reg [ 8:0] data_send   = 0; // amount of data words sent // increase it for larg
 reg [31:0] clk_count   = 0; // delay control
 reg [23:0] WS2812_data = 24'd1; // WS2812 color data
 
-wire send_bit;
-assign send_bit = WS2812_data[bit_send] & LED_MASK[data_send];
-//assign send_bit = (data_send == 0) ? WS2812_data[bit_send] : 1'b0;
-
 always@(posedge CLOCK_50)
 	case (state)
 		RESET:begin
@@ -65,7 +59,7 @@ always@(posedge CLOCK_50)
 		BIT_SEND_HIGH:begin
 			WS2812 <= 1;
 
-			if (send_bit) 
+			if (WS2812_data[bit_send]) 
 				if (clk_count < DELAY_1_HIGH)
 					clk_count <= clk_count + 1;
 				else begin
@@ -84,7 +78,7 @@ always@(posedge CLOCK_50)
 		BIT_SEND_LOW:begin
 			WS2812 <= 0;
 
-			if (send_bit) 
+			if (WS2812_data[bit_send]) 
 				if (clk_count < DELAY_1_LOW) 
 					clk_count <= clk_count + 1;
 				else begin

output_file.map

@@ -6,6 +6,6 @@ Page_0		0x00000000		0x00059D8A
 
 Notes:
 
-- Data checksum for this conversion is 0x1A5DDC5D
+- Data checksum for this conversion is 0x1A5EBC7A
 
 - All the addresses in this file are byte addresses

top.v

@@ -1,38 +1,14 @@
 module top(
-    input  wire CLOCK_50,
-    output wire WS2812_OUT
+    input  wire       CLOCK_50,
+    input  wire [4:4] D_INP,
+    output wire       WS2812_OUT
 );
 
-    localparam integer LED_NUM       = 10;
-    localparam integer TICK_1SEC     = 50_000_000;
-    localparam integer COUNTER_WIDTH = 26;
-
-    reg [COUNTER_WIDTH-1:0] sec_count;
-    reg [LED_NUM-1:0]       led_mask;
-
-    initial begin
-        sec_count = 0;
-        led_mask  = 10'b0000000001;
-    end
-
-    always @(posedge CLOCK_50) begin
-        if (sec_count == TICK_1SEC - 1) begin
-            sec_count <= 0;
-
-            // LED0 -> LED1 -> ... -> LED9 -> LED0
-            led_mask <= {led_mask[LED_NUM-2:0], led_mask[LED_NUM-1]};
-        end
-        else begin
-            sec_count <= sec_count + 1'b1;
-        end
-    end
-
     omdazz_WS2812b #(
-        .WS2812_NUM(LED_NUM),
-        .CLK_FRE     (50_000_000)
+        .WS2812_NUM(10 - 1),
+        .CLK_FRE(50_000_000)
     ) u_ws2812 (
         .CLOCK_50(CLOCK_50),
-        .LED_MASK(led_mask),
         .WS2812  (WS2812_OUT)
     );